Thrust Washer for a Tohatsu 25-30 HP, will fit Mercury 30HP

Mercury factory part.

Gorilla Duct Tape 48mm x 30m Black

5/16" Barb, 1/4" NPT Male

I can confidently recommend this Phone & Radio Waterproof Bag. We have tested and proven them to be 100% waterproof, this bag allows you to use your phone or radio in any environment without worrying about water damage. Keep your device safe and functional with this essential accessory.

This is for a single M6 x 25mm 316 stainless steel bolt.

This 1L Plastic Measuring Cup is a must-have for accurate measurements, with 100mL increments, this cup offers precise readings. Its oil and fuel resistant design makes it durable and long-lasting.

Premium Triple-Action Inflatable Pump | 29psi Max
Get on the water faster with this powerful triple-action inflatable pump, designed for boats, paddleboards, and kayaks. Featuring three selectable modes, it makes inflating easier and more efficient—whether you’re starting from empty or just topping up. Built tough to handle up to 29psi, this pump delivers reliable high pressure for a secure, firm finish every time.

Includes a specially designed adaptor for bridge port valves, ensuring a perfect fit and hassle-free setup. Compact, durable, and easy to use—this is the pump you can rely on for every adventure.

M5 316 Hex Nut

LOCTITE 263 is a red, dual cure, acrylic dimethacrylate ester fluorescent threadlocker designed for the permanent locking and sealing of threaded fasteners. It cures between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It works on active metals (e.g. brass, copper) and passive substrates such as stainless steel and plated surfaces.

This Performance Service has been designed to get your 30hp Mercury ready to race at its optimal performance. While ensuring your tilt and steering hold strong throughout the weekend.

This is recommended to be done once a season or before a major competition (North Island Championships and NZ IRB Nationals).

 Our performance 50 point check.

1. Change Gear Box Oil.
2. Adjust turning arc to within specification.
3. Water pump impeller assessed for condition*.
4. Water pump housing assessed for condition*.
5. Gear box bolts greased and tightened.
6. Prop guard bolts Loctite and tightened.
7. Prop guard veins straightened.
8. Prop guard inspected for cracks and repaired.*
9. Prop guard and prop has uniform clearance.
10. Propeller Crown nut assessed for condition*.
11. Propeller Split pin assessed for condition*.
12. Gear lever selector Loctite and tightened.
13. Recoil removed, cleaned and assessed for condition*.
14. Pull cord rope not frayed, or damaged*.
15. Pull cord handle assessed for condition*.
16. Pull cord catch assessed for condition*.
17. Recoil bolts tight and Loctite.
18. Tiller arm assembly assessed for condition*.
19. Tiller arm mount bolts greased and tightened.
20. Tiller arm tension set so it doesn’t fall.
21. Throttle linkages not worn or loose.
22. Check the motor makes full throttle.
23. Inspect the chock for function and doesn't stick.
24. Clean fuel filter.
25. Check fuel bayonet can fit easily and adjusted.
26. Fuel bayonet cleaned as required.
27. Check fuel lines are not kinked or damaged*.
28. Check spark plug leads/caps not damaged*.
29. Air Box bolts secured with Loctite.
30. Check electrical wires for damage.
31. Fuel line on gear lever side if requested.
32. Tidy electrical wires with new cable tie.
33. Tilt tube cleaned and assessed for condition*.
34. Tilt tightening when adjusted.
35. Toggle not bent*.
36. Toggles cleaned.
37. Toggle Feet Secured with Loctite.
38. Check engine mount bolt spins.
39. Tension Engine mounts.
40. Steering stiffens when bolt is tightened.
41. Power tune motor.
42. Check no arcing of electrical Leads.
43. Set Idle.
44. Set fuel mixture.
45. Compression test both chambers.
46. Grease motor nipples.
47. Check Safety Strop for condition*.
48. Engine cleaned.
49. Sandpaper fitted to gear lever.
50. Fit Cowling.

*  May require additional parts, costs are charge additionally to service price.

Please enquire with any questions

Aluminium 3 blade propeller, rubber hub.

10" diameter, 3-blades, 13" Pitch right-hand rotation.

Colour: Black

This propeller is suited for a 30hp Mercury outboard engine.

Comes with Mounts, Bolts, Washer and Nyloc Nuts.